![]() |
Overview | ![]() |
![]() |
Technology & Lead Time | ![]() |
Layer
Count Area(A)
|
Standard Time of Delivery(Day) | |||
A<1㎡ | 1≤A<3㎡ | 3≤A<5㎡ | A≥5㎡ | |
2 | 5 | 7 | 7 | 10 |
4 | 5 | 7 | 7 | 10 |
6 | 7 | 7 | 7 | 10 |
8 | 7 | 7 | 7 | 10 |
10 | 10 | 10 | 10 | 14 |
12 | 10 | 10 | 10 | 14 |
14 | 10 | 10 | 10 | 14 |
16 | 10 | 10(11) | 10(12-14) | 14(16-17) |
18 | 10(11) | 10(12) | 10(12-16) | 14(16-20) |
20 | 14 | 14 | 14 | 20 |
22 | 14 | 14 | 14 | 20 |
24 | 14 | 14 | 14 | 20 |
26 | 14 | 14 | 14 | 20 |
28 | 14 | 14 | 14 | 20 |
30 | 14 | 14 | 14 | 20 |
•The lead time is based on standard board •Standard Board Material:FR-4 •Standard Board Thickness:2-6/L≤2mm, 8-12/L ≤ 3mm, 14-18/L ≤ 4mm, 20-30/L ≤ 5mm •Surface Finish Technology:HASL,FLASH GOLD,OSP •Base Copper Thickness of Inner / Outer Layer:18/35um •No requirements of Blind Vias , Buried Vias and Special Stack up •Min. Fabrication Quantities should be more than 2 pcs •The lead time is suggested and guaranteed in the brackets |
![]() |
PCB Fabrication Capabilities | ![]() |
Manufacture Capabilities | Standard | Advanced | Future |
Outer Minimum Line Width/Spacing | 0.004 | 0.003 | 0.002 |
Inner Minimum Line Width/Spacing | 0.004 | 0.003 | 0.002 |
Min Line Edge Spacing | 0.025 | 0.020 | 0.015 |
The Highest Layer Count | 30 | 50 | 60 |
Misregistration Tolerance | +/-0.005 | +/-0.004 | +/-0.003 |
Min.Finished Copper Thickness | 0.02 | 0.01 | 0.008 |
Max.Finished Copper Thickness | 0.240 | 0.300 | 0.350 |
Min.Impedance Tolerance | -10% | -7% | -5% |
Max.Warpage | 0.10% | 0.7% | 0.5% |
Min.Plated Hole Diameter | 0.008 | 0.005 | 0.004 |
Hole Tolerance | -0.004 | -0.003 | +/-0.002 |
Max.Aspect Ratio | 12:1 | 18:1 | 20:1 |
Distance from Min.Hole to Annular Ring | 0.025 | 0.020 | 0.016 |
pad Min.Inner Layer Drilling Pad | 0.012 | 0.010 | 0.008 |
pad Min.Outer Layer Drilling Pad | 0.012 | 0.010 | 0.008 |
PTH Tolerance | -0.005 | -0.003 | +/-0.001 - +/-0.002 |
Min.Solder mask | 0.005 | 0.004 | 0.003 |
Outline Tolerance | +/-0.005 | +/-0.003 | +/-0.002 |
Min.Distance of Test Fixture | 0.020 | 0.016 | 0.01 |
Min.Distance of Flying Probe Test | 0.015 | 0.01 | 0.008 |