NOTES注释:
1.       THE FOLLOWING PHOTOPLOT FILES(.PHO),APERTURE REPORT FILES(.REP), NCDRILL, AND LAYER LIST(.LST) FILES ARE REQUIRED TO FABRICATE THIS PCB:
以下PHOTOPLOT文件（.PHO），光圈报告文件（.REP），NCDRILL
层列表（.LST）文件用于制造该PCB：
8030122-P1.PHO/COPPER, LAYER 1 TOP SIDE铜箔，顶层
8030122-P2.PHO/COPPER, LAYER 2 BOTTOM SIDE铜箔，底层
8030122-P3.PHO/PASTER MASK, TOP SIDE钢膜，顶层
8030122-P4.PHO/SOLDER MASK, TOP SIDE阻焊，顶层
8030122-P5.PHO/SOLDER MASK, BOTTOM SIDE阻焊，底层
8030122-P6.PHO/SILKSCREEN, TOP SIDE丝印，顶层
8030122-P7.PHO/DRILL DRAWING钻孔图
8030122-P8.PHO/ASSEMBLY DRAWING装配图
8030122-P9.DRL/NC DRILL DRAWING NC钻孔图
8030122-P9.LST/NC DRILL DRAWING NC钻孔图
8030122-P.REP/APERTURE FILE光圈文件
8030122-P.LST/LAYER LIST层列表
2.       MATERIAL材料:
FR-4 FINISHED TO 0.062 +/- 0.006 THICK
FR- 4  成品0.062 +/- 0.006（英寸）
3.       COPPER PLATE铜板:
COPPER LAMINATION IS 1 OZ.PLATED TO 1.5 OZ. FOR OUTSIDE LAYERS.
铜层压1 OZ.电镀后为1.5盎司。适用于所有外层。
4.       CONDUCTOR WITH AND SPACING导体和间距:
THE MINIMUM CONDUCTOR WITH AND SPACING ON THE FINISHED BOARD IS成品板最小导体间距:
WIDTH线宽– 6 MIL
SPACING线宽– 6 MIL
5.       HOLE REQUIREMENTS孔要求:
PLATED THROUGH HOLES TO BE +/-0.003 OF DEFINED SIZE AFTER REFLOW镀通孔过回流焊后为定义尺寸的+/-0.003英寸.
HOLE LOCATION TO BE +/-0.003 RELATIVE TO LOCATING REFERENCE孔位置为相对定位参考点的+/-0.003英寸.
6.       SOLDER MASK阻焊:
SOLDER MASK OVER BARE COPPER阻焊盖过裸铜.
MATTE GREEN SOLDER MASK APPLIED TO BOTH SIDES双面使用亚光绿色阻焊面膜.
7.       MARKING标记:
WHITE INDELIBLE SILKSCREEN APPLIED TO COMPONENT SIDE元器件层使用白色、不可擦除丝网印刷.
VENDOR LOGO FLAME RATING TO BE APPLIED IN COPPER ON SOLDER SIDE, 0.160 MIN. FROM ALL PADS, TRACES AND EDGES厂商标志阻燃等级适用于铜焊接层，最小0.160英寸。用于所有焊盘、印制线和边缘.
8.       MANUFACTURER TO BE U.L. RECOGNIZED, MANUFACTURE IN ACCORDANCE WITH PERFORMANCE STANDARD IPC-6011 & IPC-6012, TYP3, CLASS 2制造商为UL认可制造商，制造按照绩效标准IPC- 6011和IPC- 6012，TYP3，2级执行.
9.       NO MODIFICATION OR REPAIRS ARE PERMITTED WITHOUT APPROVAL未经许可，不得进行修改或维修.
AFTER APPROVAL MODIFICATIONS TO BE MADE IN ACCORDANCE WITH IPC-771 & IPC-7721被批准后，按照IPC- 771和IPC- 7721执行修改或维修.
10.   ALL PERIMETER DIMENSIONS IN INCHES +/-0.010所有外围尺寸公差+/-0.010（英寸）.
11.   TEST 100% FOR ELECTRICAL SHORTS AND OPENS(IF APPLICABLE) 尽可能100%测试电气开短路.